一种曲伸式 DFB 光纤激光水听器探头的研究

为了提高 DFB(分布反馈式)光纤激光水听器的声压灵敏度,改善其动态特性,设计了一种曲伸式DFB 光纤激光水听器探头结构.该结构在保持激光器原有优点的同时,通过增大声压作用面积并将压力转化为对激光腔的轴向应变,有效地实现了声压增敏,同时通过机械结构改善了水听器的动态特性.利用有限元软件 ANSYS 对该结构进行了优化设计,加工制作了备构件并对 DFB 光纤激光器进行了封装,制作出长度约80 mm、直径仅6 mm的水听器原型样品并进行了实验研究.实验结果表明,采取该种形式的结构对 DFB光纤激光器进行封装后,探头的声压灵敏度提高了约17.5 dB,在500～1 500 Hz频率范围内具有较平坦的灵敏度响应.     

Development of proxy relationships: a case study of the Lebanese Civil War

Proxy warfare is a consistent element in international warfare. However, it is unclear why proxy relationships form in cases where states have multiple options of groups to support. Existing research identifies the presence of transnational constituencies, shared interstate rivalries, and moderate relative strength of militant groups as highly influential on the development of a proxy relationship. This study examines the presence of these variables within the context of the Lebanese Civil War. The results of this demonstrate that each state places greater importance on some variables and ignores others when choosing a proxy. Additionally, this study further demonstrates the presence of new variables that are key to the development of proxy relationships.     

大口径穿甲弹用材料应用研究动态及分析

为了提高穿甲弹的威力,有效对抗新型防护装甲和防护技术,对现有提高大口径穿甲弹穿甲威力的技术途径进行了分析,得出了弹芯材料和弹托材料的力学性能是制约穿甲威力提高的关键因素。详细阐述了目前国内外在大口径穿甲弹用弹芯材料的强韧化、绝热剪切敏感性,新型复合材料弹芯的研究和轻质弹托材料的应用研究动态,并对研究中存在的问题进行了分析。最后,对我国大口径穿甲弹用材料的研究工作进行了展望。     

Enhancing the explosive characteristics of a Semtex explosive by involving admixtures of BCHMX and HMX

A well-known ternary plastic explosive, Czech Semtex 1H, contains a mixture of PETN and RDX softened by SBR. In this work, BCHMX was used to replace PETN in Semtex 1H to form Sem-BC+RDX. In addition, another mixture based on BCHMX and HMX as energetic fillers bonded by the polymeric matrix of Semtex 1H (Sem-BC+HMX) was studied. The particle size distribution of each individual explosive was determined to obtain the optimum mixing conditions. Friction and impact sensitivities were determined. The velocity of detonation was reported practically and the detonation properties were calculated by EXPLO5 code. The explosive strength of each sample was measured by the ballistic mortar test. The conclusion confirms that the velocity of detonation of Sem-BC+HMX was the highest in comparison with the prepared samples. Sem-BC+RDX has the least impact and frictions sensitivities. Sem-BC+RDX has higher detonation velocity, detonation properties and explosive strength than Semtex 1H. Addition of BCHMX in Semtex 1H as a replacement for PETN is the candidate to produce a high performance advanced Czech plastic explosive.     

立式金属油罐罐壁与底板连接区域强度分析

采用ABAQUS大型非线性有限元软件,在弹性地基的假设下,对10000m3立式金属油罐进行了水试压状态下的强度分析,计算出两种地基条件下底板的轴向位移和罐壁与底板连接区域的应力分布,所得结果与前人研究成果基本吻合,验证了有限元分析的正确性。从罐壁与底板连接区域的应力曲线可以看出,地基状况对该区域的应力大小有着显著的影响,这为进一步研究复杂边界条件下罐底边缘应力分布以及罐基的优化设计提供了参考。     

An investigation on anti-impact and penetration performance of basalt fiber composites with different weave and lay-up modes

The woven basalt fiber composites (WBFC) and the unidirectional [0°/90°/45°/-45°]_s basalt fiber composites (UBFC) were prepared by hot-pressing. Three-point bending test, low velocity impact test, and ballistic test were performed to the prepared composites. After the tests, the specimens were recovered and analyzed for micromorphology. Three-point bending tests show that both the bending strength and stiffness of the WBFC surpass those of the UBFC. Low velocity impact test results show that the low velocity impact resistance to hemispherical impactor of the UBFC is higher than that of the WBFC, but the low velocity impact resistance to sharp impactor of the UBFC is lower than that of the WBFC. For the ballistic test, it can be found that the ballistic property of the UBFC is higher than that of the WBFC. After the tests, microscopic analysis of the specimens was applied, and their failure mechanism was discussed. The main failure modes of the UBFC are delamination and fibers breakage under the above loading conditions while the main failure mode of the WBFC is fibers breakage. Although delamination damage can be found in the WBFC under the above loading conditions, the degree of delamination is far less than that of the UBFC.     

磨损身管下的杆式穿甲弹强度失效计算机模拟

针对某型105 mm钨合金超速脱壳穿甲弹在射击试验时出现的弹体强度失效现象,使用有限元分析软件对其强度进行了分析计算。计算分两种工况：正常状态下的弹体应力应变分布和磨损身管条件下的弹体应力应变分布。根据计算结果,证实了弹体强度失效是由于火炮身管过度磨损的原因所致。     

【专栏】飞机结构静强度应变现场测试手段展望

目前飞机结构静强度应变现场主要的测试手段为使用电阻应变计测量系统，但电阻应变计测量系统存在抗电磁干扰差、引线过多以及一致性难以保证等问题，测试效果难以保证。近年来，光纤传感以及非接触光学测量手段的迅速发展，为飞机结构静强度应变现场测试提供了多种选择。本文通过分析以数字图像相关法技术为代表的新技术的特点，如通过进行非接触操作消除安装过程中所带来的分散性误差以及不确定性，在应对某些需要定性分析的飞机静强度试验场合时可以实时给出三维应变和位移场数据，使测量技术更加直观，以及可溯源性更好、更容易保证计量特性的稳定等，对未来飞机结构静强度应变现场测试手段进行了展望，以期为相关部门和机构提供参考。     

高能微脉冲表面强化修复45CrNiMoVA传动轴性能试验研究

针对某大型船用传动轴工作轴颈表面产生腐蚀坑的问题,采用高能微脉冲表面强化修复技术对试验样轴进行修复。通过拉伸试验筛选了焊丝,采用光学显微镜和显微硬度计分析了修复层的显微组织和硬度,研究了扭转条件下修复层与基体的结合强度。结果表明:Ni-818焊丝修复层与基体的结合强度高,抗拉强度为557MPa;修复层显微组织均匀、致密,硬度差异小;当扭矩为200N.m,且表面最大剪应力为438MPa时,修复层和基体之间结合良好。由此得出结论:采用高能微脉冲表面强化修复技术,使用Ni-818焊丝可实现对45CrNiMoVA传动轴的表面强化修复。     

多轴越野车辆悬架部件结构优化设计

基于有限单元法、变密度方法和车辆动力学分析方法,对某型多轴越野车辆的典型部件(前悬架摆臂)主体进行了结构优化设计研究。结果表明:通过结构优化,降低了摆臂的质量,提高了摆臂的静态、动态结构刚度和强度。